Replacing uPVC Window Handles
Switching the handles of windows made of upvc is an easy task. It is important to ensure that the new handle fits into the spindle cutout of the window mechanism.
If you follow the steps below the handle of any cockspur will fit in most windows. The key is the step in the height of the handle.
What to Look For
A lot of windows in the UK are fitted with uPVC handles Over time, they may begin to show signs of wear and wear and tear. The handle on the window can become loose or difficult-to-operate when this happens. This is a fairly simple task that can be accomplished by anyone who is familiar with basic hand tools.
The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to find the fixing screws or pins that hold the handle in the position it is in. They are usually on the inside of the handle and can be removed using a screwdriver or pliers.
When the handle is loose It is best to gently pull it away from its hinges. Then, you will need to locate a replacement handle in the same style and size. This can be accomplished online or in a local DIY store, and it should take five minutes using an screwdriver.
One crucial aspect to take into consideration when replacing a uPVC window handle is the step height. This is the distance from the base of the handle until it sits on the window frame. This is a typical measurement and you should confirm the step height before ordering the replacement handle.
There are various sizes depending on the type of handle. Inline handles are offered for uPVC window with lug centres of 31mm, while cockspur handles come with lug centres of 43 millimetres. Tilt and turn handles are typically found on uPVC windows, and they feature a specific design that allows the window to be tilted in to allow for ventilation, and then turned to open the window fully.
The most common uPVC handle breakage is internal cracking, rather than a fracture from the base. This makes them difficult to open, and it is therefore essential to ensure that the replacement handle you purchase has the same length of spindle as your existing one.
Remove the Old Handle
If the handles on your windows are damaged or not properly fitted, they could cause double-glazed windows to not open or close correctly. They could even become stuck. There are a variety of reasons for this, such as general wear and tear or the corrosion of the handle made of metal. In these situations it is crucial to find replacement upvc window handles as soon as possible in order to prevent further damage and loss of functionality.
When replacing the handles of windows made of upvc it is recommended to remove the old handles from the window. Start by removing the screw covered with the handle when it is in a closed position. Once you have removed the screw, you can remove the handle. You can make the job simpler by using an electric screwdriver.
It is also worth noting that the screws on the handle could be hidden behind plastic caps, so it is recommended to take a Stanley knife to the screws and remove them. After you have removed the old handle, you'll have to examine the square cutout on the base to make sure that the new handle you choose for the window lock is compatible. It is important to measure the length of the spindle on the handle you used to replace it with and compare it to the size of the window mechanism spindle cutout.
There are three types of upvc handles: Espag handles with a central screw that can be turned left or right and Cranked handles that have two screws and Spade handles that have flat arms and can be used on either side of the upvc window. When you have a suitable replacement, it's just a matter of screwing the handle in place and ensuring that the spindle is fitted into the lock mechanism. After that, you can then tighten the handle to the window frame. The replacement upvc handle will now be secured.
Take a measurement of the Spindle
If you're looking to replace a upvc handle that has fallen, it's likely that the spindle that holds it in place is damaged or is loose. In some cases you can tighten the spindle by using pin or screw. In other cases it will require replacement completely. There are a few different types of upvc window handles. There are three types of handles: inline espagnolette, cockspur, and tilt-and-turn. Each type of handle is mounted and replaced in a different fashion.
It is essential to measure the handle before purchasing an alternative. This will ensure that the new handle is of the correct size and fits into the window. Luckily, all handles conform to industry standards of sizing making it relatively easy to identify the right size.
To measure the handle's size you must turn the window to the open position. You should be able to determine the dimensions of the pin or screw that secures the handle. Then take a tape measure or ruler to determine the length of the spindle. Once you know the length of the spindle, you can purchase a replacement one with the same length.
The step height of a window handle is another factor to take into consideration when purchasing a replacement. The step height is the distance from the base of the handle to the point at which it sits on the frame. Typically, this is about 21mm for uPVC windows and 9mm for aluminum. Dropping objects into the gap will allow you to observe how far the handle extends before it meets an obstruction.
Cockspur handles can have different backsets depending on what style of window you install them in. door handle replacement wandsworth repairmywindowsanddoors come with a standard height of 43mm centre to centre (2 fixing points). Cockspur handles have different backsets, based on the window they are placed in. This is due to the fact that they have a spur which extends from the handle and locks onto a cockspur wedge hitting plate.
Fit the New Handle
When you've picked a new handle, make sure you align it with the screw holes on the door and fix it using the screws provided. If you're also replacing the latch lever it can be put in the same way as the door handle. After that, attach the door trim to hide the mounting screws.
Tips: To remove the metal head from a wooden wedge, place the handle on the floor so that its wide end is on the ground. Then, use to tap the narrow end. Be careful not to damage the handle or spindle.